Boyle Energy

For More Information Call 610.446.2444

Service

Oil Burner Service Contracts

Service Contract ($209) show [ + ]

Oil Burner Service Agreement

2007 / 2008 Cost $209

This plan provides full coverage for labor, parts and after-hour emergency service required to maintain your comfort Under this plan, BOYLE ENERGY will provide the following:

• Annual maintenance. No after-hour labor charges for emergency service listed parts :
• Air filters (1 set per year)
• Aquastat ($50 max allowance for TRIPLE acting aquastat)
• Blower ($75 max. allowance)
• Blower motor (up to 1/3 h.p. only half the cost is covered when used with air conditioning)
• Burner Coupling
• Burner Fan
• Burner Motor
• Cad Cell and relay
• Circulator motor (up to 1/6 h.p.) and coupling (bearing and seal assembly excluded; direct drive and self contained circulator excluded)
• Combustion Chamber ($50 allowance)
• Delayed action oil valve
• Electrodes
• Emergency Toggle Switch
• Fan and limit control
• Fuel pump
• Heating thermostat, standard
• Ignition transformer
• Ignition Wires
• Nozzle
• Nozzle adapter
• Oil filter
• Single 275 gallon oil tank if tank is readily accessible ($75 max allowance)

Not covered: Stack Relay- System should be replaced

Platinum Service Contract ($299) show [ + ]

PLATINUM OIL BUNER SERVICE AGREEMENT

Cost $299

N.B. The same general conditions as our basic service agreement apply. There will be an additional charger of $10 per zone for multiple zones.

Boiler Agreement Parts:

• Altimeter gauge
• Triple Aquastat
• Automatic water feeder (hot water water system)
• Circulator bearing assembly
• Chamber 100% coverage
• Draft regulator
• Expansion Tank
• Extrol Tank
• Flo Valve
• Purging system (once per year)
• Clock Thermostat (if already present)
• Domestic Mixing Valve
• Low water cut off (not steam)
• Relief Valve
• Smoke Pipe
• Oil Tank gauge
• Zone Valve (1 per year)

Furnace Agreement Parts:

• Blower motor, regardless of horse power
• Smoke Pipe
• Oil Tank Gauge
• Warm Air Blowers and Bearings (heating season only)

N.B. The same general conditions as our basic service agreement apply.

General Conditions

• Acceptance of Coverage:
• This agreement is designed for the convenience of our fuel oil customers only. All heating oil requirements must be purchased from BOYLE ENERGY during the term of this policy.
• Failure to comply with all of the terms of this policy, render it null and void.
• BOYLE ENERGY reserves the right to inspect all equipment before accepting such equipment for Burner Service Plan coverage. Repairs required to place the burner in acceptable condition will be billed at our established rates.
• Annual Inspection and Cleaning
• It is the customer's responsibility to notify BOYLE ENERGY in order to schedule a convenient time for this annual service and to provide safe access to the heating unit. If the customer fails to notify BOYLE ENERGY to schedule this maintenance, it is known that BOYLE ENERGY will not refund any portion of this contract, nor does BOYLE ENERGY have responsibility to perform this maintenance.

Contract Terms:

This contract is automatically self-renewing for each successive year at the rates in effect at the time of each renewal, unless either party shall give 30 days prior written notice of cancellation. Contracts are due and payable upon presentation and failure to pay within 30 days will results in immediate cancellation (if you are on our budget program you may include the service contract). There will be no refunds of any unused portion of this plan although it may be transferred to new owner, subject to BOYLE ENERGY approval.

Liability:

Under no condition are we, BOYLE ENERGY, liable for damage resulting to unoccupied buildings, or for damage to their contents, or for any other loss directly or indirectly related to heating system problems of any kind under any circumstances.

It is understood that age, deterioration and improper design can cause inadequate draft in your chimney which can adversely affect the operation of you heating equipment. I (we) will hold BOYLE ENERGY, blameless for any equipment failure or damage resulting from the improper or lack of flue venting.

Additionally, under no circumstances will BOYLE ENERGY be liable for damage of any nature resulting from the malfunction or failure of any equipment (weather this equipment is covered under this agreement or not) that is the result of service work performed by anyone other than BOYLE ENERGY service personnel acting with explicit company authorization under written company policy.

The company assumes no responsibility to notify any governmental agency, including the Environmental Protection Administration in the event of tank leakage causing any contamination of the earth.

It is your duty, at all times, to see that your heater is operating properly, including while you are away from your premises for any period of time, no matter how short this period may be.

The Burner Service Plan includes only repair and replacement of parts which are specifically listed herein which are defective due to ordinary wear. Repairs involving labor or parts not covered under this plan, will be billed at our established flat rate.

A complete oil burner will not be replaced under the terms of this AGREEMENT.

Customers will be charged at our established rates for service calls resulting from: failure of customer to maintain proper water level in boiler, improper settings of thermostat or emergency switch turned off.

Both service plans offer you family comfort and peace of mind year round. Both plans provide you with 24 hour emergency service, parts and labor coverage for no heat and/or hot water calls, also a schedule tune-up to insure the greatest fuel efficiency.

[+] Back To Top

---

Products

Oil Heaters

The Tobago Boiler (Forced Hot water) show [ + ]

Oil-Fired, Hot Water Boiler for homes with chimneys

The Tobago boiler provides hot water heat in a variety of sizes (from 80,000 to 238,000 heating capacity BTU/HR) to serve a wide range of homes. An approved chimney is required.

The boiler design is proven in service to be reliable. It is easy to maintain and economical in its purchase price and fuel consumption. The boiler can be ordered with flame retention Beckett, Carlin or Riello oil burners.

The boiler features a swing-open burner door that gives full access to the combustion chamber and burner nozzle. A split jacket provides easy access to the flue passages of the heat exchanger. The attractive and durable jacket is powder-coated to resist scratching and insulated to retain heat. The heat exchangers are constructed to meet the standards set by the American Society of Mechanical Engineers.

The Tobago has a wet base design in which the heat exchanger surrounds the combustion chamber on all sides to provide optimum heat transfer. The result is lower fuel costs.

Tobago is the latest in a series of designs that is constructed for long life and designed to provide the most value for each energy dollar. That's CROWN's commitment to quality.

Features of the Tobago:

• Rugged wet base cast iron heat exchanger
• Swing-open burner door for easy service
• Choice of three oil burners
• Attractive split jacket easily removed for servicing
• Insulated to save energy
• Fully assembled, ready for installation
• Factory tested control system
• Three physical sizes with nine firing rates
• Combustion chamber with a ceramic fiber target wall with blanket
• Drain valve
• Draft regulator
• Oil solenoid valve
• Burner twist disconnect plug
• Lifetime limited warranty on the cast iron hot water heat exchanger
• Temperature/pressure gauge
• ASME relief valve
• Large cast iron flame inspection door
• Optional front-mounted tankless coil for domestic hot water
• Combination Aquastat-relay

Hi Boy Furnace (Forced Hot Air) show [ + ]

CROWN oil furnaces provide you with performance and versatility. Currently,
there are three series available - Hi-Boy, Lo-Boy and Horizontal/Counterflow.

Front Flue / Rear Flue

• Doe Output Range
• 70,500 To 117,600 BTU/HR
• 4 SIZES

Features:
Fully Packaged

• Cabinet:
  - Foil-faced fiberglass insulation reduces heat loss and noise
  - Baked enamel finish for durability
• Burner:
  - High quality Beckett Flame retention burner with primary control
• Controls:
  - Readily available trade components
  - 40 VA transformer
  - Color coded wiring for easy service
  - Transformer package and cooling fan relay are factory wired for easy add-on cooling installation
  - Barometric Damper
• Blower:
  - Slide-out design
  - 4 Speed PSG pre-lubricated motors with sealed bearings for low maintenance, maximum efficiency, and trouble-free performance
  - Dynamically balanced blower with resilient motor mounts for smooth and quiet operation

Standard Equipment

• Cabinet Construction:
  - Heavy gauge steel, Seal-Tite design, completely assembled at factory, leveling legs.
• Finish:
  - Baked enamel for greater durability.
• Burner:
  - Flame retention type. Shipped assembled in furnace.
• Controls:
  - Cad cell primary control, combination blower and limit control.
• A/C:
  - Ready for 4 Ton Cap.
• Wiring:
  - All wiring factory connected.
• Heater Exchanger:
  - Heavy 13 gauge hot rolled alloy steel. Visually hand-welded, inside and out.
• Radiator:
  - "Wrap-around" type.
• Barometric Damper
• Blower:
  - Squirrel cage type. Permanently lubricated, resilient mounted.
• Blower Motor:
  - Designed for heavy duty, continuous operation. Thermally protected.
• Blower Assembly:
  - Entire unit with motor can be easily removed for servicing.
• Filter Rack with Filters
• Flue Collector Box:
  - Completely enclosed by cabinet.
• Insulation:
  - Spun glass and aluminum foil for "hand cool" cabinet.
• Access Door:
  - Easily removed for access to burner and controls. Completely encloses controls and burner.

Gas Heater

Aruba 3 show [ + ]

Gas-fired hot water boiler
Perfect for residential and light commercial applications with chimneys

ARUBA 3 is CROWN's best selling gas-fired, hot water boiler. It comes in a wide range of sizes from 37,000 to 295,000 BTU/HR input.

Crafted with a rugged, cast iron heat exchanger and stainless steel burners that are both backed by a lifetime limited warranty, the ARUBA 3 offers proven-in-service reliability, simplicity of design and economy in its purchase price and consumption of fuel.

The ARUBA 3 is available with standing pilot or electronic ignition for greater energy efficiency. Honeywell controls provide reliability, ease and convenience.

Attractive and durable, the two-tone, powder-coated jacket resists scratching. Plus, it's insulated to retain heat. The ARUBA 3 meets all national standards, and the heat exchanger meets the specifications of the American Society of Mechanical Engineers.

ARUBA 3 is the latest in a series of designs that CROWN engineers have created for ease of use, constructed for long life and engineered to provide the most value for each energy dollar. That's CROWN's commitment to quality.

ARUBA 3 has all these features for optimum safety and performance:

For Safety:

• Can be installed directly on non-carpeted combustible floors
• Fully assembled, ready for installation
• Factory tested for flame quality, leakage, control system operation and overall performance
• Combination high limit/circulator relay control regulates water temperature
• Spill switch detects venting problems
• Rollout switch detects heat exchanger blockage
• ASME relief valve (set at 30 psi)

For Performance:

• Cast iron heat exchanger with a lifetime limited warranty
• Stainless steel burners with a lifetime limited warranty
• Built-in draft hood fits in low spaces
• Aquastat mounted directly into heat exchanger for improved response
• Reliable Honeywell controls
• Appliance quality, powder-coated jacket
• Fiber-glass insulation to minimize wasteful heat loss
• High performance circulator
• Motorized vent damper reduces chimney losses
• Temperature/pressure gauge
• Drain valve

Furnace (Forced Hot Air) show [ + ]

Ultra Gas Furnaces
95.1% AFUE Two Stage - Variable Speed

What are the benefits of Frigidaire Ultra Gas Furnaces?

Furnaces are measured using AFUE (Annual Fuel Utilization Efficiency). The higher the AFUE rating the more energy efficient your system is and the lower your energy costs will be.

The Frigidaire 95.1% efficiency furnace will deliver years of warmth and comfort. Compare this to an older furnace with a rating of 60% efficiency, you will be getting a return on your investment with lower utility bills for years ahead with a new 95.1% efficient furnace.

• This Frigidaire furnace is one of the most efficient gas furnaces available today. Besides energy savings, this furnace qualifies for a $200 Federal Tax Credit under the Energy Policy Act of 2005.
• Two stage furnaces operate like two separate furnaces to maintain a more consistent comfort level throughout your home.
• During the first stage, which is about 80% of the time, the unit will use about 68% of its heating capacity.
• Two Stage, variable-speed systems will always start in the first stage and attempt to meet the heating demand.
• Reduced capacity, efficiently warming your home on mild winter days.
• When temperatures drop the furnace automatically adjusts itself and enters the second stage to meet increased heating demand.
• The temperature in your home will only vary a couple of degrees and you will experience quiet comfort.
• Improved air filtration is delivered with two stage variable speed so you'll breathe a lot easier.
• The unique variable speed motor improves humidity control and operates quietly. In fact, in most installations it is practically silent.
• The variable speed also allows the motor to ramp up gently eliminating uncomfortable temperature swings.
• Designed for upflow applications.

Air Conditioning

Puron show [ + ]

Better Air Conditioners & Heat Pumps
14 SEER and 15 SEER- Outdoor Sections

What are the benefits of variable speed systems?

• A single stage air conditioner is sized to cool your home on the hottest day of the year.
• It delivers 100% of its cooling capacity at all times.
• When you install a 13 or 14 SEER Frigidaire air conditioner or heat pump with an indoor section featuring a GE ECM variable speed motor, you'll experience better comfort and lower utility costs.
• A Frigidaire variable speed system operates at higher efficiency. The variable speed motor can save $150 per year plus another $240 in electrical costs when your thermostat is set for continuous fan operation.
• The air conditioner automatically maintains its programmed level of air flow regardless of dynamic changes in static pressure.
• Static pressure will change with a dirty air filter, zoning changes and obstructed supply registers as an example.
• Better indoor air quality is achieved quietly and inexpensively by setting the motor to run continuously at reduced air-flow levels between cooling cycles.
• The Frigidaire variable speed system also operates quieter than conventional motors, reduces temperature swings, indoor moisture, and hot spots.
• The indoor section, a coil or air handler, completes your new air conditioner or heat pump system. With this system, a indoor coil section with a variable speed gas or oil furnace is required if you have gas or oil heat. If you have a heat pump, then the matched variable air handler section is required to complete the system.

Your Frigidaire air conditioner or heat pump has been carefully designed and engineered to give you outstanding energy efficiency and years of trouble-free operation. No detail has been left out. Frigidaire uses only proven components like the Copeland scroll compressor. It's the leaders choice for efficiency, durability, and longevity. Just another "value added" manufacturing step built into all Frigidaire products.

Freon show [ + ]

Central Air Conditioning
13-14 SEER RSE Series

The Comfort-Aire line of efficient central air conditioning features advances in technology to provide a comfortable environment. State-of-the-art condensing units are designed for single family, multi-family and light commercial applications.

The units come pre-charged and are packed features, including solid steel cabinetry, easy access control box, heavy duty compressors and efficient wraparound condenser coils.

Units are available in sizes from 1-1/2 to 5 tons.

Outstanding Warranty Coverage
The series is covered by a 12 year warranty on compressors and a six year warranty on other parts (see warranty for limitations and details).

Ductless Mini Split show [ + ]

Ductless Mini-Split Systems
DMC/DMH Mini-Splits
DMC Series Ceiling Cassette

Ductless mini-split systems solve the problem of cooling and/or heating a space when adding ductwork is impractical or too expensive. The matched combination of outdoor condenser and indoor air handler fits virtually anywhere, and is simple to install and economical to operate.

Mini-Splits are ideal for a wide range of applications:

• Residential
  Homes where it's difficult or not desirable to use a window air conditioner, renovations and restorations, additions, sunrooms, bedrooms, workshops, home offices
• Industrial/Commercial
  Warehouse offices, computer rooms, restaurants
• Specialized
  Sports arena skyboxes, nursing homes, hospitals, churches, community facilities

Installation requires a hole less than 3" in diameter to run refrigerant lines between indoor and outdoor units. Also, the indoor section uses low voltage wiring.

There's a mini-split system to fit just about any installation, from single rooms to expansive spaces. Our single, dual and tri-zone models offer an impressive array of capacities in both A/C and heat pump models.

Water Heaters

Oil Fired show [ + ]

OIL-FIRED WATER HEATERS - Residential / Light Commercial: Single Flue

Providing quality in construction, efficiency in performance and durability in operation has earned Bock a bit of a reputation: we're recognized as the leader in oil-fired water heaters.

Whatever your hot water needs, there's a Bock, just right for you:

Bock water heaters are perfect for all residential applications, particularly those with high-volume hot water demands. Today's homes not only require a dependable and economic hot water source for traditional uses like dishwashing, laundering and cleaning, but also one that offers fast recoveries to meet the demands of more sophisticated shower systems, whirlpools and radiant flooring systems

In commercial and industrial applications; from light demand to continuous-use requirements, our outstanding recovery capabilities make Bock water heaters ideal for multi-dwelling units (MDUs - apartments, dormitories), place of worship, hospitality (hotels, motels), health care (hospitals, clinics, assisted living facilities), athletic facilities, (health clubs, spas, swimming pools), hair salons and beauty shops, farms (dairy barns), office buildings, correctional facilities, laundries, car washes, food service, schools and many more.

• Turboflue-Bock's patented design is the industry's most advanced and efficient heat exchanger. Simply put, it heats water faster and uses less fuel, which reduces energy costs.
• Durable and exclusive porcelain enamel glass is used to line all tanks and Turboflues. Highly resistant to aggressive water. Fresh silica mixed daily to provide the highest quality.
• Built to last -Hand-crafted from heavy gauge steel. Longer life equals a higher "Return on Investment".
• Dual magnesium anode rods-Inhibit corrosion and maximize tank life. Electrolysis attacks the anode rods, not the welded seams of the tank.
• Double pressure tested -Only Bock pressure tests its tanks twice.
• Fully welded tank skirt -prevents noxious flue gases from escaping between the tank and jacket.
• Center flue design -reduces tank flex for longer life.
• Fiberglass insulation -decreases standby heat loss.
• Accurate temperature control-Only Bock offers dual aquastats or operating and high limits, as standard.
• Spring loaded inspection door -Easy access for inspection and maintenance, also functions as a pressure relief valve.
• Brass drain valve - accessible.
• Factory installed T&P valve - CSA listed.
• Hand-cast refractory lined combustion chamber - Onlyone in the industry - better heat retention, warmer starts, better combustion, reduces noxious emissions.
• UL listed.
• ASME construction -available on selected models.
• Externally mounted burner -provides easy installation and maintenance.
• 5 year limited warranty - on steel tank (single family residential installations).
• 3 year limited warranty -on steel tank (commercial installations).

Gas Fired show [ + ]

Defender Safety System
Energy Saver (XR) Models And Non-Defender Models

These conventional (atmospheric) vent water heaters offer "Extra Recovery" (XR) which translates to an increased amount hot water available at a usable temperature in less time than normal. 65 and 75-gallon models do not include Defender Safety System.

(Sample model numbers include: M-1-XR403S6FBN, M-2-XR504T6FBN - Non-Defender XR model numbers include: M-1-XR65T6BN, M-2-XR75S6BN)

Defender Safety System features

• Advanced ScreenLok Technology Flame Arrestor design
• Resettable thermal switch
• Piezo ingiter
• Maintenance free
• Pedestal base
• Sight window

Standard Energy Saver features

• Fully automatic controls
• Factory Installed Hydrojet Total Performance System
• Vitraglas lining
• Factory installed dielectric waterway fittings
• Flue baffle
• Protective magnesium anode rod
• Side tappings
• Snap-lock draft diverter
• T & P relief valve included
• Brass drain valve
• 2" Non-CFC foam insulation (1" on M1 models)

Generators

Generators show [ + ]